Lead2Amazon

USB 3.2Gen1 Type-A Connection, Docking Station for SATA SSD/HDD

It can be equipped with a 3.5 and 2.5 inch SATA III/II/I connection SSD and HDD drive

Each slot can hold up to 16TB The cloning function makes it easy to backup large amounts of data, or when usual, it can also be used as two large external USB drives

Simply remove the cable from your PC and press the "CLONE" button to start the clone

The elastic skip function allows you to continue copying even if there is a bad sector on the drive side of the reader (source) side

Easy to install and use HDD/SSD Supports up to 16TB HDD

2.5 and 3.5 inches can be used for a wide range of devices. The dust cover on the outlet prevents dust from entering the connector when not in use

Equipped with a power supply interlock, it can reduce unnecessary power consumption caused by forgetting to turn off the power of the main unit

It has overvoltage and overcurrent protection to protect the data in case of emergency

It can also be used as an external TV storage

【Supported SSD】FIDECO NVMe SATA SSD Docking Station can support M.2 PCIe NVMe SSD with M key or M+B key, and M.2 SATA SSD with M+B key. Supports M.2 SSD sizes 2230/2242/2260/2280/22110. One dual M.2 clone dock can meet the needs of different sizes of SSD

【20Gbps Transfer Rate】FIDECO NVMe SATA dock adopts the USB 3.2 Gen 2 standard, supports UASP, and theoretical maximum speed reach 20Gbps. No more waiting for data transfer, definitely save a lot of time

【Support Offline Clones】FIDECO NVMe SSD Clone Dock supports offline clones and is very easy to operate. Simply insert the two SSD into each slot and long press the clone button for 5 seconds to start the offline clone

【Convenient Tip】 For data transfer or offline drone, you can not insert M.2 NVMe SSD and SATA SSD at the same time. Otherwise, SSD A is only recognized and SSD B is not recognized

【ONE FOR EVERYTHING】The FIDECO M.2 clone dock comes with 1 USB C to USB C/A cable, so you can meet your needs even if you use a USB A or USB C port on your desktop or laptop

【Compatible System】FIDECO M.2 duplicator is widely compatible with Windows, Mac OS, Linux. No drivers required, just plug and play!

Note: For new hard drive SSDs, it must be initiated and recognized by your computer. Provides firmware updates and technical support. If you have any other questions, please contact [support@fideco.cn]

【One Key Two-Way Offline Drone】This SSD HDD Stand supports offline drone function, so you can create HDD SSD clones without connecting to computer. Customize the source and target disk to easily achieve two-way cloning between NVMe hard drives and SATA hard drives. Make sure the target disc is larger than the source disc

【Efficient Heat Dissipation】The SSD & HDD stand is equipped with a separate aluminum alloy heat dissipation shell for SSD and built-in heat dissipation silicone and metal heat dissipation vest to protect your hard drive from accidental damage while dissipating heat. The SSD clone base is designed with aluminum alloy construction to enhance the rigidity of your device while promoting heat discharge. Note: The heat dissipation shell cannot be used alone as a hard drive case

【NVMe & 2.5/3.5 SATA Support】The SSD & HDD stand supports both SATA and NVMe single disk read and write simultaneously; supports up to 8TB M.2 NVMe M-Key SSD (2230/2242/2260/2280) and 22TB 2.5/3.5 SATA SSD/HDD (Note: PCIE lane only, M.2 SATA SSD is not supported)

【10Gbps SSD Clone Stand】The M.2 SSD clone stand with USB3.2 Gen2 interface, can achieve high speed data transfer of 10Gbps, and the maximum data transfer rate of 2.5 & 3.5 SATA hard disk drives is 5Gbps. The included 12V3A external power adapter provides enough power for stable and efficient data transfer. (Note: Offline Drone Only. Do not connect to the computer when cloning. )

【Broad Compatibility】Support Windows, Mac OS, Linux operating systems, equipped with USB Type-A to Type-C and Type-C to Type-C 2-in-1 cable, providing multi-function connection for laptops, desktops, TVs, mobile phones (need OTG support), routers and other devices

【UASP Supported】: USB 3.0 HDD external case supports UASP & Trim protocol at transfer speeds of up to 5Gbps. HDD stand provides instant access to SATA drives for file backup, disk imaging, or data transfer. Toolless design makes hot swapping easier

【Compatible 20TB Drives】: Hard Disk Case compatible with 2.5"/3.5" SATA I/II/III HDD and SSD supports up to 20TB Serial ATA hard drives. The naked stand includes a 1m USB-A cable and power supply, which can be used in most places, small size and easy to use

(Freely Connect Devices) This hard drive stand can also be used on PC, laptop, smart TV, smart router, and PS4 devices. Compatible with Windows, Mac, Linux, iPad OS (Thunderbolt), Android and other platform operating systems. This multi-function allows you to enjoy a seamless connection with all your favorite devices. {Note: Your phone must support OTG }

【Durable Hard Drive Docking Station】: With efficient 36W 12V/3A power, SATA external hard disk case ensures the stability and maximum durability of the uninterrupted transmission process. SATA Hard Drive Case 3.5 is inactive for 10 minutes and automatically goes into sleep mode to save energy

Application Design: The USB 3.5 inch HDD case uses a dust-proof design and silicone anti-slip pad, and a host connection toolless design, hot swapping, LED indicators (blue reading, red transfer files)

(Can copy whole hard disk without a computer) You can easily copy the entire contents of the hard disk, and create a cloned drive. When replacing your old HDD with a new HDD or SSD, it is convenient for copying all the data including the system (C Drive) with the OS installed

Easy to set up. Start with a single button: Simply set the source (original) and copy destination (copy), turn it on, and press the center round button to copy the hard disk. If there is data on the HDD B, it will be overwritten. The hard disk capacity of HDD B is larger than HDD A, and the data cannot be copied

Equipped with an elastic skip function: Drives with faulty sectors that are impossible to read or write data, can forced skip and copy the error location. In addition, if the copy has a bad sector, the LED will flash fast and allow you to check it at a glance. Repair function is not included. If there is a physical error, copying is not possible. The copy may not be complete depending on the condition of the defective sector

【Compatible with 2.5 inch / 3.5 inch HDD/SSD】 Compatible with 2.5 inch and 3.5 inch HDD/SSD, so you can reuse it by setting the remaining internal hard disk or internal SSD in this product

(As an external storage of your computer) Set the internal drive and connect it to a computer, it can be used as an external storage with two drives. Equipped with an "AUTO PC Power Supply Link" feature, you can turn the device on or off in conjunction with your computer or sleep mode. (Power connection is required with included AC adapter)

Equipped with PC Power Supply Linkage Function: Equipped with an "AUTO PC Power Supply Link" function, you can turn the power supply on or off in conjunction with your computer or sleep mode

Dust Intrusion Protection Cover: The 2.5 inch outlet has a hard drive cover, so the connector is closed when not in use. Even if you don't use it for a long time, you can prevent dust from entering

2BAY stand HDD/SSD duplicator case that can copy whole hard disk without a PC

Equipped with an elastic skip function, it can copy hard drives with bad sectors

Simply insert the hard disk into the BAY and press the "CLONE" button on the top for easy duplicate

Supports SATA3 for fast copying up to 440MB/s

The front is also equipped with highly visible LEDs that show the progress during the duplicate process

With SATA III compatibility, the SSD clone time is reduced by about 45% compared to our previous models. Measured with 128GB SSD Actual measurements in our measuring environment. Depending on your environment

A docking station that connects to a computer with a USB Type-C (TM) connector to connect a USB device or HDMI display. One cable connects all the peripherals needed to a USB Type-C (TM) computer

Unique design for stable connection Designed to stabilize the quality of data communication between a computer and a docking station with measurements taken according to the certification test of transmit and reception signals. It minimizes the compatibility problem between connected devices and provides a smooth operating experience

1 USB Type-C (TM) port compatible with USB Power Delivery Connect the USB Type-C compatible AC charger to power your device and unit at a maximum of 100 W. Since the product consumes 15 W, the actual output is up to 85 W. If you need power supply at 85W, please prepare an AC charger with 100W output

Super Fast Data Transfer USB 10 Gbps (USB 3.2 (Gen2) USB Type-C port x1 and 2 USB-A ports

It is equipped with an HDMI port that can output video from a computer to an external monitor (Supported resolution: up to 4K/60Hz)

Press the power button: Same dimensions and color as the macmini m4 and m4 pro. There is a space between the main unit and the macmini has a hole for the power button

Heatsink: Considering heat dissipation, there is a space between the mac mini and the exterior is made of aluminum alloy. We also included a high thermal conductive silicone pad to stick to the M.2 SSD

Multi-Monitor Support: The HDMI on the back allows you to add a monitor. HDMI cable is not included

M.2 Slots: It can be equipped with a high-speed, high-capacity M.2 SSD

Easy Setup: Set up is complete by simply connecting 2 USB cables. A separate USB power adapter (recommended power value: 18 W)

HDD / SSD Supported: This is a hard disk case that can be equipped with both a 3.5-inch HDD and a 2.5-inch HDD/SSD. Supports up to 64GB of 4 16TB SSD up to 2TB

(Compatible with USB 3.2 (Gen2) Standard) Supports high-speed communication USB 3.2 (Gen2) that can maximize the performance of the SSD

(Prevents Forget to Turn Off / Energy Saving Design) Equipped with a power supply link function that detects the power status of your computer, and automatically returns to sleep. Depending on your PC, it may not be compatible with sleep interaction

(Equipped with Auto FAN Control) Auto-cooling fan control with a high-noise fan function, which allows you to adjust the rotation of the fan to cool efficiently

[Type-C Compatible/Safe Design] The USB 3.2 (Gen2) compatible Type-C cable does not have the difference between the top and bottom of the connector, so you don't have to worry about the wrong direction of the plug. Furthermore, it has a secure design that holds the built-in HDD/SSD securely with accessories such as a jump prevention cover and a fixed handle