Lead2Amazon

Luminous Flux: Approx. 1,500 lm

Product Size: Width 3.8 x Depth 5.1 x Height 14.2 inches (9.6 x 13 x 36.2 cm); Weight: 1.3

Lighting Mode: Switch between 3 levels of brightness (High=100%, Medium=50%, Low=10%)

Luminous Flux: Approx. 1,500 lumens

Angle adjustment: open and close = 0 ~ 90 degrees (7 positions in 15 degrees), rotations/minute = 0 ~ 270 degrees (free rotation / minute without knuring)

Country of Manufacture: Body: China; Battery Pack: Japan; Charger: China.

Chuck: One-touch bit lock system (stepped dimensions of 0.35, 0.45, 0.51 inches (9, 11.5, 13 mm)).

Maximum Torque: High Speed: 17.7 in-lbs (2.0 N·m); Low Speed: 53.1 in-lbs (6.0 N·m).

Number of Revolutions: High Speed: 900 RPM; Low Speed: 300 RPM.

Clutch Operating Torque: 21 settings (approx. 0.3–4.0 N·m [3–41 kgf/cm] in increments of approx. 0.19 N·m [1.9 kgf/cm]).

Screw Tightening: High mode: For small screws, iron (M4×0.4 in (10 mm) with spring washer), approximately 2,300 pieces; Low mode: For small screws, iron (M5×0.3 in (8 mm), approximately 1,800 pieces. High mode: For wood screws, spruce (φ0.13x0.8 in/φ3.5×20 mm), approximately 310 pieces; Low mode: For coarse thread, spruce (φ0.15x1.0 in /φ3.8×25 mm), approximately 270 pieces; Low mode: For Tek screws, iron (φ0.16x0.5 in/φ4×13mm, plate thickness 0.03 in/0.8mm), approximately 140 pieces.

Drilling: Low mode: For woodwork, plywood panels (φ0.6 x 0.5 in/15 x 12 mm), approximately 55 holes; For metalwork, iron (φ0.2 x 0.03 in/φ6 x 0.8 mm), approximately 60 holes.

Maximum tightening torque (N·m) drill: 3

Number of beats: 0-3000

No-load RPM: 0 - 2,600

No-load rotational speed (min-1) Drill: 0-600

Total Length: 7.3 inches (186 mm)

Type: Single item

Packaging Size: 17.7 inches (45.0 cm) x 14.0 inches (35.5 cm) x 7.3 inches (18.5 cm)

Country of origin: Body: China; Battery Pack: Japan; Charger: China.

Rotational Speed: 18V 10,000 rpm, 14.4V 8,001 rpm; Specifications: Dustproof, IP56 Water resistant

Dustproof/ Waterproof Rating: IP56

Rotation Torque: 18 V = 6.7 N·m {68 kgf·cm}, 14.4 V = 5.4 N·m {55 kgf·cm}

Rotation Speed: 18V = 0 - 4,500 RPM (rotations per minute), 14.4 V = 0 - 3,600 RPM.

Cutting depth: 0 - 1.8 inches (0 - 46 mm) (only for right angle cutting)

Product Dimensions / Weight: 18 V = Total Length 13.5 x Height 9.0 x Total Width 6.3 inches (343 x 228 x 160 mm); 6.1 lbs (2.75 kg); 14.4 V = Total Length 13.2 x Height 9.0 x Width 6.3 inches (336 x 228 x 160 mm); 5.7 lbs (2.6 kg) (with battery pack)

This listing is only for the main productBattery pack and charger not included

Product Size (W x D x H): 4.5 x 8.7 x 6.5 inches (11.6 x 22

Weight: 6.1 lbs (2.9 kg)

Rotor type: Single stage type

Drive Type: Direct

Vacuum reach (1 Pa = 7.5 microns): 135 microns (18 Pa)

Exhaust speed (time from flow measurement): 6.9 gal/min (20.6 L/min (at 14.4 V), 9.1 gal/min (25.8 L/min) (at 18 V)

Intake port diameter: 5/16" male flare

Working time (estimated and fully charged): Approximately 120 minutes (when using EZ9L54/EZ9L48)

Accessories: Pump Oil 5.1 fl oz (150 ml) EZ9X320

Protection Rating: IP5X (dustproof)

Compatible Voltage: 14.4 V/18 V Dual Tool

Number of Strokes: 6,000 strokes per minute

Cutting depth: Woodworking = 0.6 inches (15 mm), Plaster = 1.2 inches (30 mm)

Orbital: Fixed type

Cutting Capacity Estimated (full charge/drywall 0.4 inch (9.5 mm) 2 sheets/drilling for light fixtures): Cutting Size 23.6 x 23.6 inches (600 x 600 mm), Number of Cuts: Approximately 45 holes, Cutting Size 17.7 x 17.7 inches (450 x 450 mm), Number of Cuts: Approximately 50 holes

Cutting capacity estimated (fully charged, drywall 0.4 inch (9.5 mm) 2 sheets/hole for ceiling ventilation fan): Cutting size: 11.8 x 11.8 inches (300 x 300 mm), Number of cuts: Approximately 75 holes

Estimated Cutting Capacity (fully charged, drywall board 0.37 in (9.5 mm) x 2 sheets/hole for inspection ports): Cutting Size 18.9 x 18.1 in (457 x 457 mm), Number of Cuts: Approximately 50 holes

Estimated cutting capacity (fully charged/drilling holes for switches/outlets): Cutting size 2.2 x 3.7 inches (55 x 95 mm) (plaster board 0.5 inches (12.5 mm)); Number of cuts: Approximately 210 holes

Estimated cutting capacity (fully charged/drilling holes for switches/outlets): Cutting size: 2.2 x 3.7 inches (55 x 95 mm) (0.5 inches (12 mm) (0.5 inches (12 mm)), Number of cuts: Approximately 120 holes

Light Source: Visible light semiconductor laser 25.0 inches (635 mm)

Output: 1 mW or less, Class 2

Lower light: High brightness LED

Line width: 0.1 inch (2.5 mm) or less / 16.4 ft

Lead direction: gimbal mechanism (horizontal retention mechanism)

Correction angle: Approx. +-4 degrees

Line stop time: about 5 seconds

Instruction Accuracy: +-3 mm/10 m

Power Supply: 1 AA alkaline battery (1.5 V) (sold separately)

Continuous Usage Time: Approx. 8 hours (Panasonic alkaline batteries) at 48°F (20°C)

Product Size (W x D x H): 4.5 x 8.7 x 6.5 inches (11.6 x 22

Weight: 6.1 lbs (2.9 kg)

Rotor type: Single stage type

Drive Type: Direct

Vacuum reach (1 Pa = 7.5 microns): 135 microns (18 Pa)

Exhaust speed (time from flow measurement): 6.9 gal/min (20.6 L/min (at 14.4 V), 9.1 gal/min (25.8 L/min) (at 18 V)

Intake port diameter: 5/16" male flare

Working time (estimated and fully charged): Approximately 120 minutes (when using EZ9L54/EZ9L48)

Accessories: Aluminum case EZ9666, pump oil 5.3 fl oz (150 ml) EZ9X320

Maximum tightening torque: 18 V = 160 Nm (14.4 V = 155 Nm)

Product Size (W x D x H): 4.6 x 9.3 x 2.4 inches (11.8 x 23.5 x 6.1 cm); Weight: 2.7 lbs (

Accessories: 18V 3.0Ah battery pack (EZ9L53) x 2, charger (EZ0L81), case (EZ9648)

Rotational Speed: Strong Mode = 0 - 2,500 rpm, Medium Mode = 0 - 1,450 rpm, Low Mode = 0 - 950 rpm, Tex Mode = 0 - 2,500 rpm

Country of Origin: Body: China, Battery: Japan, Charger: China